Mold Remediation >> Mold Tester Certification

There is substantial visible mold growth inside hard surface (e.g., sheet metal) ducts or on other components of your heating and cooling system. There are several important points to understand concerning mold detection in heating and cooling systems: Many sections of your heating and cooling system may not be accessible for a visible inspection, Mold Tester Certification so ask the service provider to show you any mold they say exists. 

You should be aware that although a substance may look like mold, a positive determination of whether it is mold or not can be made only by an expert and Mold Tester Certification may require laboratory analysis for final confirmation. For about $50, some microbiology laboratories can tell you whether a sample sent to them on a clear strip of sticky household tape is mold or simply a substance that resembles it. 

If you have insulated air ducts and the insulation gets wet or moldy it cannot be effectively cleaned and should be removed Mold Tester Certification and replaced. If the conditions causing the mold growth in the first place are not corrected, mold growth will recur. Additional Resource U.S. Dept. of Agriculture, Food Safety and Inspection Service fact sheet -Safe Food Handling.

Molds on Foods: Are They Dangerous? September 2005 A Brief Guide to Mold in the Workplace, U.S. Dept. of Labor, Occupational, Safety and Health Administration, Mold Tester Certification Safety and Health Bulletin 03-10-10Indoor Air Regulations and Mold Standards or Threshold Limit Values (TLVs) for airborne concentrations of mold, or mold spores, have not been set. 

Currently, there are no EPA regulations or standards for airborne mold contaminants. Large Buildings and Mold EPA has a number of resources available, Mold Tester Certification you can start with the Indoor Air Quality Building Evaluation and Assessment Model (I-BEAM). I-BEAM updates and expands EPA's existing Building Air Quality guidance and is designed to be comprehensive state-of-the-art guidance for managing IAQ in commercial buildings. 

This guidance was designed to be used by building professionals Mold Tester Certification and others interested in indoor air quality in commercial buildings. I-BEAM contains text, animation/visual, and interactive/calculation components that can be used to perform a number of diverse tasks. See www.epa.gov/iaq/largebldgs/i-beam/index.html. 

See also"Building Air Quality: A Guide for Building Owners and Facility Managers".Excerpt from the Building Air Quality: A Guide for Building Owners and Facility Managers,Appendix C - Moisture, Mold and Mildew: How to Identify the Cause of a Mold and Mildew Problem. Mold and mildew are commonly found on the exterior wall surfaces Mold Tester Certification of corner rooms in heating climate locations. 

An exposed corner room is likely to be significantly colder than adjoining rooms, Mold Tester Certification so that it has a higher relative humidity (RH) than other rooms at the same water vapor pressure. If mold and mildew growth are found in a corner room, then relative humidity next to the room surfaces is above 70%. However, is the RH above 70% at the surfaces because the room is too cold or because there is too much moisture present (high water vapor pressure)?

The amount of moisture in the room can be estimated by measuring both temperature and RH at the same location and at the same time. Suppose there are two cases. In the first case, Mold Tester Certification assume that the RH is 30% and the temperature is 70 F in the middle of the room. The low RH at that temperature indicates that the water vapor pressure (or absolute humidity) is low. 

The high surface RH is probably due to room surfaces that are "too cold." Temperature is the dominating factor, Mold Tester Certification and control strategies should involve increasing the temperature at cold room surfaces.In the second case, assume that the RH is 50% and the temperature is 70oF in the middle of the room. The higher RH at that temperature indicates that the water vapor pressure is high and there is a relatively large amount of moisture in the air. 

The high surface RH is probably due to air that is "too moist." Humidity is the dominating factor, Mold Tester Certification and control strategies should involve decreasing the moisture content of the indoor air. Schools and Mold and Indoor Air Quality The Agency's premier resource on this issue is the Indoor Air Quality Tools for Schools kit. 

Our schools-related resources on the web start. The asthma companion piece for the IAQ Tools for Schools Action kit, Mold Tester Certification is Managing Asthma in the School Environment -www.epa.gov/iaq/schools/managingasthma.html. This publication has a section entitled Clean Up Mold and Moisture Control: An excerpt follows: Common Moisture Sources Found in Schools 

Moisture problems in school buildings can be caused by a variety of conditions, including roof Mold Tester Certification and plumbing leaks, condensation, and excess humidity. Some moisture problems in schools have been linked to changes in building construction practices during the past twenty to thirty years. These changes have resulted in more tightly sealed buildings that may not allow moisture to escape easily. 

Moisture problems in schools are also associated with delayed maintenance or insufficient maintenance, due to budget and other constraints. Temporary structures in schools, such as trailers Mold Tester Certification and portable classrooms, have frequently been associated with moisture and mold problems.Suggestions for Reducing Mold Growth in Schools 

Reduce Indoor Humidity Vent showers Mold Tester Certification and other moisture-generating sources to the outside. Control humidity levels and dampness by using air conditioners and de-humidifiers. Provide adequate ventilation to maintain indoor humidity levels between 30-60%. Use exhaust fans whenever cooking, dishwashing, and cleaning in food service areas.

Inspect the building for signs of mold, moisture, leaks, Mold Tester Certification or spills Check for moldy odors. Look for water stains or discoloration on the ceiling, walls, floors, and window sills. Look around and under sinks for standing water, water stains, or mold. Inspect bathrooms for standing water, water stains, or mold. 

Do not let water stand in air conditioning or refrigerator drip pans.Respond promptly when you see signs of moisture and/or mold, or Mold Tester Certification when leaks or spills occur Clean and dry any damp or wet building materials and furnishings within 24-48 hours of occurrence to prevent mold growth. Fix the source of the water problem or leak to prevent mold growth. 

Clean mold off hard surfaces with water and detergent, and dry completely. Absorbent materials such as ceiling tiles, Mold Tester Certification that are moldy, may need to be replaced. Check the mechanical room and roof for unsanitary conditions, leaks, or spills. Prevent moisture condensation Reduce the potential for condensation on cold surfaces (i.e., windows, piping, exterior walls, roof, or floors) by adding insulation.

Floor and carpet cleaning Remove spots and stains immediately, using the flooring manufacturer’s recommended techniques. Use care to prevent excess moisture or cleaning residue accumulation and ensure that cleaned areas are dried quickly. In areas where there is a perpetual moisture problem, do not install carpeting (i.e., by drinking fountains, by classroom sinks, Mold Tester Certification or on concrete floors with leaks or frequent condensation).

Water Damage Restoration For Electronics

Second, although self-healing does occur in the conductive polymer due to degradation of the polymer's conductivity at high temperatures, this self-healing mechanism is not thought to be as effective as the self healing mechanism of MnO2-based tantalum capacitors. Decomposition of the conductive pol  read more..

Storm Damage

Applying for a reimbursement grant from FEMA can be a time-consuming but worthwhile process. Like many government agencies there are endless types of forms and finding the correct one may be difficult. Like any type of reimbursement there are deadlines where the forms would have to be submitt  read more..

Black Mold Health Risks

Wet vacuums are vacuum cleaners designed to collect water. They can be used to remove water from floors, carpets, and hard surfaces where water has accumulated. They should not be used to vacuum porous materials, such as gypsum board. Wet vacuums should be used only on wet materials, Mold Remediation Black Mold Health Risks as sp  read more..

Clean Up Water Damage Carpet

Installation shall be in accordance with an approved design and plan. Details of construction shown on the drawings but not included herein are considered as a part of this specification. Construction activities shall be in accordance with applicable OSHA regulations.SITE PREPARATION Clearing and&nb  read more..

Basement Flood Cleanup

When returning to your home after a hurricane or flood, be aware that flood water may contain sewage. Protect yourself and your family by following these steps:Inside the Home Keep children and pets out of the affected area until cleanup has been completed. Wear rubber boots, rubber gloves, and Water Damage Basement Flood Cleanup  read more..

Snake Removal in Garden

Most people like to have a nice garden the more plan to have, the better, but having a lush garden could also invite Animal Damage Snake Removal in Garden. I'm not sure if you know this but most snakes are not dangerous and most certainly do not want a confrontation with a human. Even the venomous snakes will not attack un  read more..

Storm Damage

If your home has sustained a significant amount of Dehumidification Storm Damage because the roof was damaged and the rainwater leaked through. There is a certain procedure that should be followed to minimize the possibility of any other damage like the growth of mold or any other structural damage. Your home should   read more..

How To Remove Fire Damage From Furniture

Nineteen fire chiefs from around the world will participate in the National Fire Protection Association (NFPA) Urban Fire Forum in Boston, October 19-22. Also in attendance will be R. David Paulison. Fire Damage How To Remove Fire Damage From Furniture

Paulison is currently the Under Secretary of Federal Emergency Management/Direct  read more..

Water Damage

Water is by far the single most long-term destructive substance in any indoor environment. It will dissolve or weaken many building materials and supports the growth of microorganisms like mold. Because it can flow, Sewage Cleanup Water Damage has the unique capability to carry with it a wide variety of hazardous p  read more..

How To Dispose Of Asbestos Siding In Texas

This mandatory appendix specifies the procedure for analyzing air samples for asbestos and specifies quality control procedures that must be implemented by laboratories performing the analysis. The sampling and analytical methods described below represent the elements of the available monitoringÂ&n  read more..