Wind Damage >> Water Removal

Tell your local Water Removal construction supply retailer the size and number of openings you require to cover to decide how many sheets to buy. To place plywood shutters you will require bolts, wooden or mason anchors, bigger washers, and 5/8 - inch outside-graded plywood. For windows that are 3 feet by 4 feet or smaller placed on a wooden framed house, use 1/4 -inch lag bolts and plastic-coated permanent anchors.

  1. The lag bolts shall penetrate the edge and frame surrounding the windows at least 1 1/2 inches. For bigger windows, utilize 3/8 –inch lag bolts that penetrate the edge and frame surrounding the Water Removal windows at least 2 1/2 inches. For windows 3 feet by 4 feet or littler placed on a mason house, use 1/4-inch expansion bolts and coated permanent expansion anchors. The expansion bolt shall penetrate the edge at the least 1 1/2 inches. For bigger windows, utilize 3/8 –inch expansion bolts that penetrate the edge at the least 1 ½ inches.
  2. The tools you will require are a circular or hand saw, a drill with the appropriately sized bits, hammers, and wrenches to fit the bolts. To be secure, use eye protections and labor gloves. Cut all of the Water Removal plywood to the measurements for every opening. Drill holes 2 1/2 inches from the outside edge of the plywood at every corner and at 12-inch intervals. Drill four holes in the middle vicinity of the plywood to relieve pressure during a typhoon. Spot the plywood over the opening and mark every orifice position on the outside edge. Drill holes with the appropriate size and type of bit for the anchors.
  3. Place the anchors, the Water Removal plywood, and the bolts to make certain they fit right. On wooden-framed houses, make sure that the anchors are secured into the solid wood that frames the door or window and not into the siding or the trim. Mark every Water Removal shutter so you will know where it is to be placed and store them and the bolts in an accessible spot. If the opening is bigger than one sheet of plywood, you will require making shutters with 2x4 bracing. This bracing could be two 2x4s at the middle and bottom of the two sheets of plywood, evenly spaced, with the 2-inch side attached to the inside of the storm shutter.
  4. Attach the 2x4s to the outside of the storm shutter with 2-inch, 10-gauge wooden screws before placing the shutter. The recommendations in this article are not intended to change local building law requirements or to serve as the only options for protecting your house from typhoon wind damage. For more information on protecting your house from typhoon wind damage, contact your local Water Removal construction officials; your local construction supply retailer; or a construction professional, such as an engineer, architect, or experienced contractors.

Animal Control And Wildlife Management

The National Historic Preservation Act (NHPA) of 1966, and its implementing regulations (36 CFR 800), requires federal agencies to: 1) determine whether activities they propose constitute "undertakings" that can result in changes in the Animal Damage Animal Control And Wildlife Management character or use of historic properties. 

  read more..

How To Become Certified To Remove Lead Paint

If an environmental covenant is to be executed for the site related to other aspects of a cleanup(e.g., restricted use soil cleanup standards were used or soil contamination is left on-site under a cap), the Operation and Maintenance Plan can be included as an attachment to the covenant. If no coven  read more..

Sewage Backup During Flooding

Protecting Your Home From Back Flow The sewage/septic system is designed to remove sewage from a house. If flood water enters the system, the sewage can backup and enter your home. To help prevent this, install a backflow valve in the sewer line. The backflow valve is opened by the flow of sewage ex  read more..

Structural Drying

When hiring the appropriate cleaning or Fire Damage Structural Drying subcontractors and your contents are going to require the storage of repaired items until they are needed. Professional fire damage and water damage restoration services might be the best resource of thorough cleaning and restoring your person  read more..

How To Remove Asbestos Flooring Adhesive

Workplace exposures at the facility after 1992 were probably much lower than exposures that occurred prior to 1992 because Libby ore was no longer used at the facility after 1992. In 2000, EPA measured 0.0107 structures/cc in Asbestos Abatement How To Remove Asbestos Flooring Adhesive air next to the exfoliation ovens (EPA 2001). 
<  read more..

Blue Water Carpet Cleaning

This is our decision regarding the Application for Further Review of Protest No. 2704-08-100508, timelyfiled on behalf of Rug Doctor, LP ("Rug Doctor"), concerning the classification of carpet cleaning machines Water Extraction Blue Water Carpet Cleaning under the Harmonized Tariff Schedule of the United States ("HTSUS").   read more..

How To Deal With A Hoarder Mother

What is the definition of compulsive hoarding? There is a three-part definition to compulsive hoarding behavior:1. It is the accumulation of, and failure to discard, a large number of possessions that appear to be useless or of limited value.2. Living spaces become so cluttered that they can't be us  read more..

How To Remove Lead Paint From Wood

There are several ways to remove lead-based paints: Wire brushing or wet hand scraping with the aid of a non-flammable solvent or abrasive compound. Liquid paint removers can be used on small areas, such as windowsills, doors and woodwork. Read and follow the manufacturer's instructions and warning   read more..

Toxic Mold

Mold gradually destroy the things they grow on. Prevent damage to building materials and furnishings, save money, and avoid potential health risks by controlling moisture and eliminating mold growth Concern about indoor exposure to mold has been increasing as the public becomes aware that exposure  read more..

Basement Drying

Once you are satisfied that the logic board is cleaned and contacts also are cleaned, you may use the hairdryer on its coldest setting and dry the logic board. You may also want to place the Electronic Restoration Basement Drying device under a lamp, such as a desk lamp, to gently warm and further dry the cleaning fluid. You c  read more..