Wind Damage >> Emergency Board Up

Plywood shutters that you create yourself, if placed correctly, could provide a high degree of Emergency Board Up coverage from flying debris during a storm. Plywood shutters could be placed on all kinds of houses. Measure every window and every door that has glass, and add 8 inches to all the height and width to provide a 4-inch overhang on every side of the window or door. Pieces of plywood are generally 48 inches by 96 inches (4 x 8 feet).

  1. Inform your local hardware supply store the dimensions and amount of openings you require to cover the Emergency Board Up to decide how many pieces of plywood to buy. To place plywood shutters, you may require bolts, wood or brick anchors, big washers, and 5/8-inch exterior-grade plywood. For windows 36 × 48 inches or littler placed on a wood framed house, utilize 1/4-inch lag bolts and plastic-coated durable anchors. The lag bolts shall intrude the wall and framed area the window at minimum 1-3/4 inches. For bigger windows, utilize 3/8-inch lag bolts that intrude the wall and framed area the window at minimum 2-1/2 inches. For windows 36 × 48 inches or littler placed on a brick house, utilize 1/4-inch expansion bolts and galvanized durable 2 inch expanding anchors.
  2. The expansion bolt shall intrude the wall at minimum 1-1/2 inches. For bigger windows, utilize 3/8-inch expansion bolts that intrude the wall at minimum 1-1/2 inches. The items you may require are a circular or hand saw, a bore with the accurately dimensioned bits, a mallet, and a spanner to fit the bolts. To be secure, utilize eye coverage and work gloves. Saw the plywood to the measurements for every opening. Bore holes 2-1/2 inches from the outside edge of the plywood at every corner and at 12-inch intervals. Bore four holes in the center area of the plywood to relieve pressure during a strong Emergency Board Up storm.
  3. Place the Emergency Board Up plywood over the opening, and mark every hole position on the outside wall. Bore holes with the appropriate dimensions and type of bit for the anchors. Place the anchors, the plywood, and the bolts to create sure they fit correctly. On wood-framed houses, create sure that the anchors are secured into the solid wood that framed the door or window and not into the siding or trim. Mark every shutter so you may know where it is to be placed, and store the shutters and the bolts in an accessible place.
  4. If the opening is bigger than one sheet of plywood, you may require you to create shutters with 24 × 48 bracing. This bracing could be two 24 × 48s at the middle and bottom of the two pieces of plywood, evenly spaced, with the 2-inch side attached to the inside of the Emergency Board Up storm shutter. Attach the 24 × 48s to the outside of the Emergency Board Up storm shutter with 2-inch, 10-gauge wood screws before placing the shutter. Impact-resistant windows are optimal for windows not easily fitted with hurricane shutters or those that are hard to reach.

Flood Water Backing Up

Steps to Responding to a Water Emergency The Water Department is dedicated to providing San Diego with a safe and reliable water supply. While the Water Operations Division and Capital Improvements Program help to maintain and improve our water system, Water Damage Flood Water Backing Up unexpected water emergencies sti  read more..

How To Make A Dry Basement Waterproofing

The results reported in Appendix B for the modeled energy savings show the same patterns as those for a foundation wall with no rim joist and no above-grade exposure. Specifically, the first R-5 of insulation produces a significant basement energy savings of 52% with only an additional 12 % of   read more..

Tools For Restoring Water Damaged Electronics

The electrochemical process involves deposition of a suitable conductive seed layer inside the porous slug.This layer is electrically contacted and the slug is dipped in a doped monomer solution. Electric current is passed through the seed layer into the doped monomer solution stimulating the oxidat  read more..

Mold Remediation

A lack of clear level reliance between levels 1 and 3 suggests that this piece of the tolerance purpose might reflect merely "noise-level" displeasure that would happen if Odor Control Mold Remediation level ever surpassed the threshold. Butanol equaling purposes gotten with aeration rates of 2.5 and 5/s"' per resident,   read more..

Debris Removal From The Colorado Floods

2013 Floods  Guidance: Landfill Management of Flood Debris Air Pollution Control Division / Stationary Sources Program The Department will exercise enforcement discretion for landfills which exceed their permitted waste acceptance limit as a result of flood debris disposal. This relief is speci  read more..

How To Clean Up Cigarette Smoke Odor

Saitoh and Inukai contend that humidity is probably the most important factor in determining the amount of corrosion that occurs [80]. They also note that the combustion gases from materials such as wood and asphalt that are not expected to produce HCl still produce corrosion. They surmise the prese  read more..

House Water Leaks

This fact sheet will help you identify and locate water leaks in your home or business. Repairing water leaks is a great way to reduce the use of water that is just being wasted. It's Only a Small Drip...Right? Slow drips of water can add up quickly. A toilet that "keeps running" after you flush or   read more..

Colorado Floods Causing Debris Removal

2013 Floods – Guidance: Landfill Management of Flood Debris Air Pollution Control Division / Stationary Sources Program The Department will exercise enforcement discretion for landfills which exceed their permitted waste acceptance limit as a result of flood debris disposal. Flood Damage Colorado Floods Causing Debris Removal

Thi  read more..

Lead Paint Exposure To Iron Workers

Field measurements using a tape measure of 12 of the cuts revealed that the paint was stripped back an average of 1.15 (range of 0.5 to 4.0 inches) inches from the cut line (based on 69 measurements taken). After hot cutting, Lead Paint Removal Lead Paint Exposure To Iron Workers burned paint provided visual evidence that stripping was insuffi  read more..

How To Clean An Electronic Circuit Board After A F

Collected papers from scientific and technical conferences, symposia, seminars, or other meetings sponsored or cosponsored by NASA. SPECIAL PUBLICATION. Scientific, technical,or historical information from NASA programs,projects, and mission, often concerned with Electronic Restoration How To Clean An Electronic Circuit Board After A F subjects having substantial pub  read more..